PULLEY


Pulley:

01-standard pulley-spun end curve crown pulley-steel pulley-straight faced pulley-pulley mechanism-pulley ratio-pulley size-pulley selection

The diameters of standard pulleys are: 200, 250, 315, 400, 500, 630, 800, 1000, 1250, 1400 and 1600 mm. pulley may be straight faced or crowned. The crown serves to keep the belt centered. The height of the crown is usually 0.5% of the pulley width, but not less than 4 mm. The pulley diameter Dp depends on the number of plies of belt and may be also be determined from the formula:

Dp > K.i (mm)

Where

K = a factor depending on the number of plies (125 to 150)

i = no of plies

The compound value should be rounded off to the nearest standard size. While selecting the pulley diameter it should be ascertained that the diameter selected is larger than the minimum diameter of pulley for the particular belt selected.

The drive pulley may be lagged by rubber coating whenever necessary, to increase the coefficient of friction. The lagging thickness shall vary between 6 to 12 mm. The hardness of rubber lagging of the pulley shall be less than that of the cover rubber of the running belt.

Pulley types:


Pulleys are manufactured in a wide range of sizes, consisting of a continuous rim and two end discs fitted with hubs. In most of the conveyor pulleys intermediate stiffening discs are welded inside the rim. Other pulleys are self cleaning wing types which are used as the tail, take-up, or snub pulley where material tends to build up on the pulley face. Magnetic types of pulleys are used to remove tramp iron from the material being conveyed.

Typical welded steel pulley-Drum conveyor pulley

01-typical welded steel pulley-pulley types-pulley design-pulley system-pulley problems-pulley size

Spun end curve crown pulley

01-conveyor pulleys-spun end crown pulley-self cleaning wing pulley-snub pulley-pulley face-magenetic pulley

Spiral drum conveyor pulley

01-spiral drum conveyor pulley-pulley types-pulley with ball bearings-pulley for handling bulk load

Welded steel pulley with diamond grooved lagging

01-types of pulley-welded steel pulley-grooved lagging-belt conveyor drive-belt conveyor resistance-belt wrapping over pulleys

Welded steel pulley with grooved Lagging

01-welded steel pulley with grooved lagging-pulley types-belt conveyor speed reduction mechanism-belt conveyor drive arrangement

Spiral Wing Conveyor pulley

01-spiral wing conveyor pulley-belt conveyor calculation-belt conveyor formula-belt conveyor gallery

 

Power calculation for the drive unit:

The horse power required at the drive of a belt conveyor is derived from the following formula:

H.P = Te . V

Where

Te is the effective tension in the belt in N

V = velocity of the belt in m/s

The required effective tension Te on the driving pulley of a belt conveyor is obtained by adding up all the resistances.

Explore posts in the same categories: MECHANICS

Tags: , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , ,

You can comment below, or link to this permanent URL from your own site.

3 Comments on “PULLEY”

  1. Juana Vaeth Says:

    I wished to thanks for this excellent study!! I surely savoring each small little bit of it I’ve you bookmarked to check out out new things you post…


  2. I acquired very good information from a weblog


  3. he weblog was how do i say it… relevant, finally something that helped me. Many thanks


Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s


%d bloggers like this: