Vertical screw conveyors

A vertical screw conveyor conveys material upward in a vertical path. It requires less space than some other types of elevating conveyors. Vertical screw conveyor can handle most of the bulk materials provided there is no large lump. The maximum height is usually limited to 30m.

A vertical screw conveyor consists of a screw rotating in a vertical casing. The top bearing for the screw shaft must be designed to stand against radial and thrust loads. A suitable inlet port at the lower end and a discharge port at the upper end of the casing are provided. Feeding a vertical screw conveyor deserves careful consideration. Most materials are fed to the vertical conveyor by a straight or offset horizontal feeder conveyor. The ideal operation of a vertical screw conveyor is to have a controlled and uniform volume of material feeding.

Uneven feeding and start stop operation may adversely affect the performance of the vertical screw conveyor in terms of speed, capacity and horse power.

Average capacities and speeds of vertical conveyor

Nominal diameter of screw in mm	Capacities in m3/hr	Speed of screw
150	10	Up to 400 RPM
250	35	300 RPM
300	75	250 RPM
400	170	200 RPM

Vertical screw conveyors or some special design of vertical screw conveyor finds wide application in ship unloading.

Practical experience with these conveyors has shown that the resistance factor for vertical conveyors is higher than those of the horizontal conveyors. Resistance factor λ may be taken as 5.5 to 7.5 for grains. 6.5 to 8.3 for salt.

The driving power of the loaded screw conveyor is given by:

P = P_H + P_N + P_st

Where,

P_H = Power necessary for the progress of the material

P_N = Driving power of the screw conveyor at no load

P_st = Power requirement for the inclination of the conveyor

Power necessary for the progress of the material P_H:

For a length L of the screw conveyor (feeder), the power PH in kilo watts is the product of the mass flow rate of the material by the length L and an artificial friction coefficient λ, also called the progress resistance coefficient.

P_H = I_m.L. λ.g / 3600 (kilowatt)

= I_m.L. λ / 367 (kilowatt)

Where,

I_m = Mass flow rate in t/hr

λ = Progress resistance coefficient

Each material has its own coefficient λ. It is generally of the order of 2 to 4. For materials like rock salt etc, the mean value of λ is 2.5. For gypsum, lumpy or dry fine clay, foundry sand, cement, ash, lime, large grain ordinary sand, the mean value of λ is 4.0.

In this connection it should be noted that the sliding of the material particles against each other gives rise to internal friction. Other resistance due to grading or shape of the output discharge pattern contributes to the resistance factor. That is why the parameter λ is always higher than that due to pure friction.

Drive power of the screw conveyor at no load, P_N:

This power requirement is very low and is proportional to the nominal diameter and length of the screw.

P_N = D.L / 20 (Kilowatt)

Where,

D = Nominal diameter of screw in meter

L = Length of screw conveyor in meter

Power due to inclination: P_st

This power requirement will be the product of the mass flow rate by the height H and the acceleration due to gravity g.

P_st = I_m.H.g / 3600

= I_m.H / 367

H should be taken positive for ascending screws and will be negative for descending screws.

Total power requirement:

The total power requirement is the sum total of the above items

P = (I_m (λ.L + H) / 367) + (D.L /20) (Kilowatt)

BELT DRIVES

Types and Selection of Drives:

• Single Unsnubbed Bare / Lagged pulley Drive
• Snubbed Bare / Lagged Pulley Drive
• Tandem Drive
• Special Drives

Single Unsnubbed Bare / Lagged Pulley Drive:

This is the simplest drive arrangement consisting of a steel pulley connected to a motor and the belt wrapped round it on an arc of 180°. This can be used for low capacity short center conveyors handling non-abrasive material. The pulley may be lagged to increase the coefficient of friction.

Snubbed Bare / Lagged Pulley Drive:

Here the angle of wrap is increased from 180° to 210° or even up to 230°, by providing a snub pulley to the driving pulley. In majority of medium to large capacity belt conveyors, handling mild abrasive to fairly abrasive materials, 210° snub pulley drive with load pulley lagged with hard rubber is adopted.

Tandem drive:

Here belt tension estimated to be high; the angle of wrap is increased by adopting tandem drives. Both of tandem pulleys are driven. The tandem drive with arc of contact from 300° to 480° or more can operate with one or two motors. The location of such drive is usually determined by the physical requirements of the plant and structural constraints.

Special Drive:

Special drives with snub pulleys and pressure belts used in heavy and long conveyors.

PULLEY

Pulley:

The diameters of standard pulleys are: 200, 250, 315, 400, 500, 630, 800, 1000, 1250, 1400 and 1600 mm. pulley may be straight faced or crowned. The crown serves to keep the belt centered. The height of the crown is usually 0.5% of the pulley width, but not less than 4 mm. The pulley diameter D_p depends on the number of plies of belt and may be also be determined from the formula:

D_p > K.i (mm)

Where

K = a factor depending on the number of plies (125 to 150)

i = no of plies

The compound value should be rounded off to the nearest standard size. While selecting the pulley diameter it should be ascertained that the diameter selected is larger than the minimum diameter of pulley for the particular belt selected.

The drive pulley may be lagged by rubber coating whenever necessary, to increase the coefficient of friction. The lagging thickness shall vary between 6 to 12 mm. The hardness of rubber lagging of the pulley shall be less than that of the cover rubber of the running belt.

Pulley types:

Pulleys are manufactured in a wide range of sizes, consisting of a continuous rim and two end discs fitted with hubs. In most of the conveyor pulleys intermediate stiffening discs are welded inside the rim. Other pulleys are self cleaning wing types which are used as the tail, take-up, or snub pulley where material tends to build up on the pulley face. Magnetic types of pulleys are used to remove tramp iron from the material being conveyed.

Typical welded steel pulley-Drum conveyor pulley

Spun end curve crown pulley

Spiral drum conveyor pulley

Welded steel pulley with diamond grooved lagging

Welded steel pulley with grooved Lagging

Spiral Wing Conveyor pulley

 

Power calculation for the drive unit:

The horse power required at the drive of a belt conveyor is derived from the following formula:

H.P = T_e . V

Where

T_e is the effective tension in the belt in N

V = velocity of the belt in m/s

The required effective tension T_e on the driving pulley of a belt conveyor is obtained by adding up all the resistances.