PULLEY

Pulley:

The diameters of standard pulleys are: 200, 250, 315, 400, 500, 630, 800, 1000, 1250, 1400 and 1600 mm. pulley may be straight faced or crowned. The crown serves to keep the belt centered. The height of the crown is usually 0.5% of the pulley width, but not less than 4 mm. The pulley diameter D_p depends on the number of plies of belt and may be also be determined from the formula:

D_p > K.i (mm)

Where

K = a factor depending on the number of plies (125 to 150)

i = no of plies

The compound value should be rounded off to the nearest standard size. While selecting the pulley diameter it should be ascertained that the diameter selected is larger than the minimum diameter of pulley for the particular belt selected.

The drive pulley may be lagged by rubber coating whenever necessary, to increase the coefficient of friction. The lagging thickness shall vary between 6 to 12 mm. The hardness of rubber lagging of the pulley shall be less than that of the cover rubber of the running belt.

Pulley types:

Pulleys are manufactured in a wide range of sizes, consisting of a continuous rim and two end discs fitted with hubs. In most of the conveyor pulleys intermediate stiffening discs are welded inside the rim. Other pulleys are self cleaning wing types which are used as the tail, take-up, or snub pulley where material tends to build up on the pulley face. Magnetic types of pulleys are used to remove tramp iron from the material being conveyed.

Typical welded steel pulley-Drum conveyor pulley

Spun end curve crown pulley

Spiral drum conveyor pulley

Welded steel pulley with diamond grooved lagging

Welded steel pulley with grooved Lagging

Spiral Wing Conveyor pulley

 

Power calculation for the drive unit:

The horse power required at the drive of a belt conveyor is derived from the following formula:

H.P = T_e . V

Where

T_e is the effective tension in the belt in N

V = velocity of the belt in m/s

The required effective tension T_e on the driving pulley of a belt conveyor is obtained by adding up all the resistances.

MECHANICAL ENGG QUESTIONS

1. What is the importance of the Thermodynamics in the field of Mechanical Engineering?
All the mechanical engineering systems are studied with the help of thermodynamics. Hence it is very important for the mechanical engineers.

2. How many Laws of Thermodynamics are there?
There are three laws of the thermodynamics.

First Law: Energy can be neither created nor destroyed. It can only change forms.In any process in an isolated system, the total energy remains the same.

Second Law: When two isolated systems in separate but nearby regions of space, each in thermodynamic equilibrium in itself, but not in equilibrium with each other at first, are at some time allowed to interact, breaking the isolation that separates the two systems, and they exchange matter or energy, they will eventually reach a mutual thermodynamic equilibrium. The sum of the entropies of the initial, isolated systems is less than or equal to the entropy of the final exchanging systems. In the process of reaching a new thermodynamic equilibrium, entropy has increased, or at least has not decreased.

Third Law: As temperature approaches absolute zero, the entropy of a system approaches a minimum.

3. State Laws of conservation of energy?
According to the laws of conservation of energy, “energy can neither be created nor be destroyed. It can only be transformed from one form to another.”

4. Is the boiler a closed system?
Yes definitely the boiler is a closed system.

5. What is Carnot engine?
It was being designed by Carnot and let me tell you that Carnot engine is an imaginary engine which follows the Carnot cycle and provides 100% efficiency.

6. Which formula forms a link between the Thermodynamics and Electro chemistry?
Gibbs Helmholtz formula is the formula which forms the link between the thermodynamics and electromagnetism.

∆Hs/R = [∂ lnp /∂ (1/T)]x

where: x – mole fraction of CO2 in the liquid phase
p – CO2 partial pressure (kPa)
T – temperature (K)
R – universal gas constant
α – mole ratio in the liquid phase (mole CO2 per mole of amine)

7. Which is the hardest compound known?
Diamond.

8. What is Hess Law?
According to the Hess law the energy transfer is simply independent of the path being followed. If the reactant and the product of the whole process are the same then same amount of energy will be dissipated or absorbed.

9. Which has more efficiency: Diesel engine or Petrol engines?
Off course Diesel engine has the better efficiency out of two.