AUTOMOBILE ENGINES

The working of an automobile engine follows the same principle as an internal combustion engine. Air, from outside, enters the engine through the air cleaner and reaches the throttle plate.
The pedal in your car is the control for the amount of air that you would want to be taken in, and you control it by pressing on this gas pedal.
The air is then distributed through the intake manifold of the cylinders.

At some point fuel is injected into the air stream, and the mixture vaporizes and is drawn into the cylinders as they start their intake stroke.

This way, when the cylinder has reached its bottom, it has drawn in sufficient mixture. As it moves up, compressing the mixture, the spark plug ignites the mixture, and as the powerful gas formed expands, it pushes the cylinder to the bottom with the cylinder once again drawing in the mixture.

In designing automobile engines, you need to be a specialist in automobile engineering.
The consideration that is taken while designing such an engine is whether it should be a carburetor or a diesel one. carburetor engines are most commonly found in passenger cars and low capacity trucks, while trucks with a capacity over two tons are fitted with diesel engines, including dump trucks, trailer tractors and bus.

Increasingly the medium and low-capacity vehicles are being fitted with diesel engines, since the fuel consumption of these engines are 30% to 50% lower than the carburetor engines.
Diesel engines not only cost more, but maintenance is much more expensive than the other type of engine. Diesels require more metal parts per kilowatt.
The critical parts of diesel engines are made of alloy steel, and the fuel injection system is much more expensive than carburetor engines.

However, the cost of manufacturing carburetor engines has increased with the use of higher mechanical grade components, considering the thermal loads of the material used. At the same time the use of high alloys and increase in production costs have contributed to the higher price of such engines.

There is a sharp rise in using aluminum alloys in design of carburetor engines in passenger cars, and with the use of high octane petrol, the cost of operation of these cars have come down extensively. Using alloy steel in constructing the engine body and other parts of the engine, makes the car lighter and hence fuel consumption goes down substantially.

The main parts that are made of high steel alloy are the main casting of the engine, the cylinder head, water and oil pumps, oil filter housing, end covers of the generator and starter, and the intake pipes. It has been observed that by using high steel alloys, the weight of the car is reduced by 35%.

The power per liter, per unit of piston area, and the brake effective pressure are 6% to 8% lower in air-cooled engines, compared to engines having liquid cooling mechanism. This is due to the fact that in engines with liquid cooling there are great losses in cylinder charging caused by the high temperature in pipes, ducts in the head, cylinder walls and head, etc.

The size of air cooled engines are much bigger than the engines with liquid cooling having the same capacity, and this is because the cylinder axes difference is larger in air-cooled engines. Taking account of the radiator dimensions, if both engines are compared, the air-cooled engine will vary slightly with its height a little longer than or approximately the same length as the water-cooled engine. As far as the width and the height is concerned both engines are about the same.

The auxiliary units of the feed and ignition, and generator and starter systems are a bit difficult to fit on the body of the air-cooled engines, because of the presence of hoods and having a danger of over-heating.

INFRARED CURVING

The coatings and paint industries strive to provide high technology coatings while reducing volatile organic compounds and energy consumption to produce a finished coating. Conventionally Convection ovens are used to cure the coatings. But this process which uses electric heaters is not an optimal process and is associated with various disadvantages.

Improved technologies are available today, which can either replace or improve the convection curing process. Infrared Curing is such a technology which uses Infrared rays emitted by an Infrared emitter to provide the required cure. Infrared curing applies light energy to the part surface by direct transmission from an emitter. Some of the energy emitted will be reflected off the surface, some is absorbed into the polymer and some is transmitted into the substrate.

This direct transfer of energy creates an immediate reaction in the polymer and cross linking begins quickly once the surface is exposed to the emitter. Infrared emitters are often custom manufactured to suit the production demand. The various aspects of Infrared curing and convection curing and the possibility of combining these two technologies into a singe system will be discussed in this seminar.

How it Works

Infrared heating is a direct form of heating. The source of the heat (the infrared emitter or lamp) radiates: energy that is absorbed by the product directly from the emitter. That is, the heat energy is not transferred through an intermediate medium. This is one reason for  the  inherent high-energy efficiency of infrared systems. For  example, hot air heating  first needs to heat air; the air then heats the product by convection.

Infrared  energy is directed  to  the  product. When  the  product absorbs this energy, it is then converted into heat. Infrared energy is dispersed from the source in much the same  way as visible light. Exposed product surfaces easily absorb  the  infrared  energy and  become  heated. Therefore, heating effectiveness is related to line-of-sight between the source and the product. Depending on the coating and/or product substrate material, this heat is further thermally conducted.

The ability of the product to absorb energy is also known as its “emissivity”. A theoretical body that absorbs all energy is termed a “black body”. A black body has an emissivity of 1. A highly reflective body would have a low emissivity value, approaching 0. (Reflectivity is the inverse of emissivity).

The potential of a product to become heated with infrared is related to the following:
• Watt density (total output power) of the source
• Wavelength (temperature) of the source
• Distance from the source to the product
• Reflective characteristics of the oven cavity
• Air movement and temperature in the oven
• Time product is exposed to the source
• Ratio of exposed surface area to the mass of the product
• Specific heat of the product
• Emissivity of the product
• Thermal conductivity of the product

CURING

Curing is a process of baking surface coatings so as to dry them up quickly. Curing is a broad term which means all the techniques employed for the finishing operations incurred during part production. Curing essentially involves either the melting of the coating or evaporation of volatile fluids present in the coating by the application of heat energy.

Curing is given to a wide range of materials both organic and inorganic. Usually curing is given to materials like ,

” Paints
” Enamel
” Liquor
” Powder coatings
” Varnishes
” Epoxy coatings
” Acrylic coatings
” Primers Etc.

Curing is also given to Rubber and Latex .The principle used for curing can also be used for drying rice and grains.

CONVECTION CURING

Convection ovens are usually used for curing purposes. Traditional convection ovens use heated forced air to provide the necessary cure. Convection ovens consist of a chamber lined on the inside with Electric heaters. The shape of the chamber will be in accordance to the shape or geometry of the part being cured. A series of blowers circulate the heated air around providing the required cure. This process depends on convection to transfer heat from hot air to body surface and conduction to transfer heat to the interior of the surface. The air being delivered is held at temperature using closed-loop control, which provides predictable, repeatable results. Typically a temperature of around 250-500 degree Fahrenheit is required for paint or powder. Though convection ovens are widely used today they have certain disadvantages, which chokes the overall productivity of a company
Disadvantages of convection ovens :

” Fairly long heating times:-

Convection is a slow process. It takes a considerable amount of time for the heaters to heat up and raise the temperature of air to the required level. This causes a lag in the process and hence the curing time increases. Longer curing time spells reduced assembly line movement. This in turn reduces productivity.

” High energy consumption:-

A convection column dryer uses around 2000 BTU(British Thermal Unit) of energy to remove 1 pound of moisture. They use around 7.7 KW of electrical energy to dry a ton of rice. These are significantly larger figures for any company trying to bring energy consumption under control. The additional use of blowers and compressors further increases energy consumption.

” Large floor area required:-

Convection ovens are bulky in nature. Due to the presence of compressors and blowers, additional space is needed, which in turn increases the floor area requirement.

” Air circulation is required:-

Convection heating requires a medium for transmission of heat. Hence blowers are employed for good circulation of heated air. This increases the overall cost of the equipment.

MAGNETIC BEARING TECHNOLOGY

Magnetic bearings have been utilized by a variety of industries for over a decade with benefits that include non-contact rotor support, no lubrication and no friction.

Conventional mechanical bearings, the kind that physically interface with the shaft and require some form of lubrication, can be replaced by a technology that suspends a rotor in a magnetic field, which eliminates friction losses.

There are two types of magnetic bearing technologies in use today – passive and active.  Passive bearings are similar to mechanical bearings in that no active control is necessary for operation. In active systems, non-contact position sensors continually monitor shaft position and feed this information to a control system.  This in turn, based on the response commanded by the system, flows to the actuator via current amplifiers.  These currents are converted to magnetic forces by the actuator and act on the rotor to adjust position and provide damping.

Additional benefits of magnetic bearings include:

• No friction
• No lubrication
• No oil contamination
• Low energy consumption
• Capacity to operate within a wide temperature range
• No need for pumps, seals, filters, piping, coolers or tanks
• Environmentally friendly workplace
• Impressive cost savings

In practice, these attractions are balanced in order to maintain a gap between the shaft (rotor) and static parts (stator). The function of the magnetic bearing is to locate the shaft’s rotation axis in the center, reacting to any load variation (external disturbance forces),

Floating rotors could boost compressor efficiencies

Traditional centrifugal compressors are based on low-speed drives, mechanical gears and oil-film bearings, resulting in high running costs because of their high losses, wear, and need for maintenance.

This new compressor drive (above) uses a permanent magnet motor, operating at an efficiency of around 97%, to drive a rotor “floating” on magnetic bearings, which spins the compressor impeller at speeds of around 60,000 rpm. These drives experience almost no friction or wear, and need little maintenance. They also minimize the risk of oil contamination, and result in compressors that are about half the size of traditional designs.

How they work

 

Magnetic bearings are basically a system of bearings which provide non-contact operation, virtually eliminating friction from rotating mechanical systems. Magnetic bearing systems have several components. The mechanical components consist of the electromagnets, position sensors and the rotor. The electronics consist of a set of power amplifiers that supply current to electromagnets. A controller works with the position sensors which provide feedback to control the position of the rotor within the gap.

The position sensor registers a change in position of the shaft (rotor). This change in position is communicated back to the processor where the signal is processed and the controller decides what the necessary response should be, then initiates a response to the amplifier. This response should then increase the magnetic force in the corresponding electromagnet in order to bring the shaft back to center. In a typical system, the radial clearance can range from 0.5 to 1 mm.

This process repeats itself over and over again. For most applications, the sample rate is 10,000 times per second, or 10 kHz. The sample rate is high because the loop is inherently unstable. As the rotor gets closer to the magnet, the force increases. The system needs to continuously adjust the magnetic strength coming from the electromagnets in order to hold the rotor in the desired position.