MATERIAL HANDLING

Bases on Design features and operational characteristics, material handling equipment may be broadly classified as:

Hoisting Equipment’s:

It constitute a group of equipment which are employed mainly for lifting or lowering of unit load or piece goods in batches. This group of equipment’s can be further sub classified into:

1. Pure Hoisting Machineries

• Jack
• Winches
• Hand Hoists
• Pulley Blocks

2. Cranes

• EOT Crane
• Jib Crane
• Cantilever Crane

3. Elevators

• Lift
• Bucket Elevators

Conveying Equipment’s:

It comprises of a number of equipment which are employed for handling principally bulk load (occasionally piece goods or unit load may also be handled) in continuous flow. Such machines do not have separate lifting or lowering gear. This group of equipment also can have further sub classifications as:

1. Belt Conveyor

2. Hydraulic Conveyor

3. Pneumatic Conveyor

4. Apron Conveyor

5. Screw Conveyor

6. Flight Conveyor

Surface/ Overhead Equipment’s:

These are the group of equipment’s which are employed for handling unit load or bulk load in batches on a horizontal surface. This group of equipment may be further sub classified into:

1. Truck and Lorries

2. Railway Cars and Wagons

3. Fork Lifts

4. Overhead mono-rail / Equipment

5. Scrapers and Skidders

Types of Material Handling Equipment Loads:

It usually classified into:

1. Unit Load

2. Bulk Load

Unit Load:

Unit loads are those which are counted by numbers or units. A component of a machine, a complete machine, a structural element, a beam, a girder, building block are some examples of unit load.

Sometimes certain quantities of free flowing materials can be placed in a container and can be handled as unit load. Hoisting equipment are primarily used for handling unit load. Unit loads are usually specified by it’s weight.

Bulk Load:

When the load is in the form of particles or lumps of homogeneous materials or powder like materials, which can not be counted by numbers, it is called as “Bulk load”.

Examples are:

Sand, Cement, Coal, Mineral, Stone, Clay etc.,

A bulk material may be classified by it’s:

1. Bulk Density

2. Lump-Size

3. Flowability

4. Abrasiveness

5. Miscellaneous Characteristics

CONVEYOR

Conveyor Take-up Arrangement:

All belt conveyors require the use of some form of take-up device for the following reasons:

• To ensure adequate tension of the belt leaving the drive pulley so as to avoid any slippage of the belt
• To ensure proper belt tension at the loading and other points along the conveyor
• To compensate for changes in belt length due to elongation
• To provide extra length of belt when necessary for splicing purpose.

Usually there are two types of take up arrangements.

• Fixed take up device that may be adjusted periodically by manual operation
• Automatic take up devices for constant load type

In a screw take up system the take up pulley rotates in two bearing blocks which may slide on stationery guide ways with the help of two screws. The tension is created by the two screws which are tightened and periodically adjusted with a spanner. It is preferable to use screws with trapezoidal thread t decrease the effort required to tighten the belt.

The main problem with the use of manual take-up is that it requires a vigilant and careful operator to observe when take up adjustment is required. Perfect tension adjustment with this system is also not possible. For this reason these devices are used only in case of short conveyors of up 60 m length and light duty.

In automatic take up arrangement the take up pulley is mounted on slides or on a trolley which is pulled backwards by means of a steel rope and deflecting pulleys. The carriage travels on guide ways mounted parallel to the longitudinal axis of the conveyor, i.e., horizontally in horizontal conveyors and at an incline in inclined conveyors. Hydraulic, pneumatic and electrical take up devices are also used.

Automatic take-up has the following features:

• It is self adjusting and automatic
• Greater take-up movement is possible.